Eval » Historie » Version 26
Maximilian Seesslen, 25.02.2026 15:24
| 1 | 1 | Maximilian Seesslen | h1. Eval |
|---|---|---|---|
| 2 | |||
| 3 | 10 | Maximilian Seesslen | Vom Bett aus kann ich nicht mal Licht ein- oder ausschalten. |
| 4 | Ein akkustischer Alarm kann auch nicht quittiert werden. |
||
| 5 | Theoretisch reicht ein einzelner button. |
||
| 6 | |||
| 7 | 19 | Maximilian Seesslen | Name: takki (IS for "Knopf") |
| 8 | |||
| 9 | 21 | Maximilian Seesslen | !takki_crop.png! |
| 10 | 20 | Maximilian Seesslen | |
| 11 | 24 | Maximilian Seesslen | https://upload.wikimedia.org/wikipedia/commons/a/a0/Power_off_icon.svg |
| 12 | 26 | Maximilian Seesslen | ZH ist 3.7mm hoch |
| 13 | 24 | Maximilian Seesslen | |
| 14 | 10 | Maximilian Seesslen | h2. Realization |
| 15 | |||
| 16 | -Slider would not have adequate resolution.- |
||
| 17 | 1 | Maximilian Seesslen | Usecase is only on/off. Single Button could do the job. |
| 18 | 2 | Maximilian Seesslen | Fancy ring would be nice. |
| 19 | 3 | Maximilian Seesslen | 90°-LEDs zeigen alle nach 'innen'. |
| 20 | 12 | Maximilian Seesslen | "LEDs":https://www.tme.eu/de/katalog/led-dioden-smd-bunt_113363/?params=1113:1500429,1550549_led-diodenausfuhrung:abgewinkelt,horizontal&queryPhrase=LED |
| 21 | |||
| 22 | 13 | Maximilian Seesslen | 0602 actually is 0603 when lying. diameter of 2mm is needed. No much space to hide. Just glow from bottom. |
| 23 | red + green. |
||
| 24 | |||
| 25 | Having it look like an mini-CANDis. |
||
| 26 | |||
| 27 | 25 | Maximilian Seesslen | 1mm Acryl |
| 28 | 3mm Acryl |
||
| 29 | 1,6mm PCB |
||
| 30 | 2mm Acryl |
||
| 31 | 1mm Acryl |
||
| 32 | |||
| 33 | 14 | Maximilian Seesslen | LEDs: |
| 34 | 7 | Maximilian Seesslen | * Orange, low ambient light |
| 35 | * Blue, bright ambient light |
||
| 36 | 12 | Maximilian Seesslen | * Red, alarm |
| 37 | 7 | Maximilian Seesslen | |
| 38 | h2. PCB |
||
| 39 | |||
| 40 | 9 | Maximilian Seesslen | 30x30mm; viel zu klein, touch keys koennen nicht mit ground hinterlegt werden. |
| 41 | 60x60mm; mit "Bauch"; 3 keys; etwas gross |
||
| 42 | 40x40mm; mit "Bauch"; On/Off+Mode; Bauch nur 5mm hoch |
||
| 43 | 1 | Maximilian Seesslen | logo/sensor 10x10 |
| 44 | 9 | Maximilian Seesslen | |
| 45 | 18 | Maximilian Seesslen | 30x60mm; Like a Mini-CANDis |
| 46 | 9 | Maximilian Seesslen | |
| 47 | 1 | Maximilian Seesslen | border 5mm; thick enough for LWL? There are some with 2mm diameter |
| 48 | 18 | Maximilian Seesslen | |
| 49 | 9 | Maximilian Seesslen | |
| 50 | 16 | Maximilian Seesslen | h2. Dimensions |
| 51 | |||
| 52 | 1 + 3 + 1,6 + 2 + 1 = 8,6 thickness |
||
| 53 | 17 | Maximilian Seesslen | CANDis is only 6mm? probably 8mm |
| 54 | 3 | Maximilian Seesslen | |
| 55 | h2. MCU |
||
| 56 | |||
| 57 | 4 | Maximilian Seesslen | * STM32L552CCT6 way too big |
| 58 | 23 | Maximilian Seesslen | * STM32F042 has a touch sensor controller according to datasheet, copilot says "no". I tested it on STM32F042 eval board. WOrks nice. |
| 59 | 4 | Maximilian Seesslen | |
| 60 | h2. To be verified |
||
| 61 | |||
| 62 | * Use Miniminutnik Acryl plates to check if text is readable/illuminated |
||
| 63 | 5 | Maximilian Seesslen | ** Looks very nicely |
| 64 | 4 | Maximilian Seesslen | * Prepare STM32F42x eval board |
| 65 | 22 | Maximilian Seesslen | ** -One touch area directly, another via JST- |
| 66 | 6 | Maximilian Seesslen | ** CANBus |
| 67 | ** Debug |