Eval » Historie » Version 12
Maximilian Seesslen, 08.01.2026 15:15
| 1 | 1 | Maximilian Seesslen | h1. Eval |
|---|---|---|---|
| 2 | |||
| 3 | 10 | Maximilian Seesslen | Vom Bett aus kann ich nicht mal Licht ein- oder ausschalten. |
| 4 | Ein akkustischer Alarm kann auch nicht quittiert werden. |
||
| 5 | Theoretisch reicht ein einzelner button. |
||
| 6 | |||
| 7 | h2. Realization |
||
| 8 | |||
| 9 | -Slider would not have adequate resolution.- |
||
| 10 | 1 | Maximilian Seesslen | Usecase is only on/off. Single Button could do the job. |
| 11 | 2 | Maximilian Seesslen | Fancy ring would be nice. |
| 12 | 3 | Maximilian Seesslen | 90°-LEDs zeigen alle nach 'innen'. |
| 13 | 12 | Maximilian Seesslen | "LEDs":https://www.tme.eu/de/katalog/led-dioden-smd-bunt_113363/?params=1113:1500429,1550549_led-diodenausfuhrung:abgewinkelt,horizontal&queryPhrase=LED |
| 14 | |||
| 15 | 7 | Maximilian Seesslen | LEDs: |
| 16 | * Orange, low ambient light |
||
| 17 | * Blue, bright ambient light |
||
| 18 | * Red, alarm |
||
| 19 | 12 | Maximilian Seesslen | |
| 20 | 7 | Maximilian Seesslen | |
| 21 | h2. PCB |
||
| 22 | |||
| 23 | 9 | Maximilian Seesslen | 30x30mm; viel zu klein, touch keys koennen nicht mit ground hinterlegt werden. |
| 24 | 60x60mm; mit "Bauch"; 3 keys; etwas gross |
||
| 25 | 40x40mm; mit "Bauch"; On/Off+Mode; Bauch nur 5mm hoch |
||
| 26 | 1 | Maximilian Seesslen | logo/sensor 10x10 |
| 27 | 9 | Maximilian Seesslen | |
| 28 | |||
| 29 | 1 | Maximilian Seesslen | border 5mm; thick enough for LWL? There are some with 2mm diameter |
| 30 | 9 | Maximilian Seesslen | |
| 31 | 3 | Maximilian Seesslen | |
| 32 | h2. MCU |
||
| 33 | |||
| 34 | 4 | Maximilian Seesslen | * STM32L552CCT6 way too big |
| 35 | * STM32F042 has a touch sensor controller according to datasheet, copilot says "no". |
||
| 36 | |||
| 37 | h2. To be verified |
||
| 38 | |||
| 39 | * Use Miniminutnik Acryl plates to check if text is readable/illuminated |
||
| 40 | 5 | Maximilian Seesslen | ** Looks very nicely |
| 41 | 4 | Maximilian Seesslen | * Prepare STM32F42x eval board |
| 42 | 6 | Maximilian Seesslen | ** On touch area directly, another via JST |
| 43 | ** CANBus |
||
| 44 | ** Debug |